How to Set Up and Calibrate a TRONXY VEHO Printer With Klipper
A practical Klipper setup guide for TRONXY VEHO printers: placement, Z tilt correction and 36-point mesh levelling, PID, input shaping, pressure advance, OrcaSlicer profiles and tips to stop large prints from warping.
Last updated: 2026-11-16 Author: Layerline Editorial Team
A step-by-step setup guide for VEHO printers: placement, Z tilt and 36-point mesh levelling, input shaping, pressure advance, OrcaSlicer profiles and first large print tips.
Setting up a TRONXY VEHO printer with Klipper comes down to six steps: place the machine on a stable surface with enough room, level the gantry and bed (Z tilt correction plus a 36-point mesh), set the Z offset, tune input shaping and pressure advance, load a matching profile in OrcaSlicer, and prepare your first large print against warping. This guide explains each step using standard Klipper procedures. It applies to the VEHO 800 Pro, 600 Pro V3, 500 Pro and VEHO 4, which all run Klipper firmware according to the manufacturer.
The exact menu names on your printer's touchscreen can differ between models and firmware versions, so this guide uses standard Klipper commands and general descriptions. Always follow the manufacturer's quick-start guide for assembly and safety steps first.
Step 1: Unboxing and choosing a location
The first step is to put the printer on a surface that is level, rigid and big enough. A wobbly table shows up as ringing in your prints.
| Model | Machine size (W x D x H) | Weight |
|---|---|---|
| VEHO 800 Pro | 1040 x 1103 x 1211 mm | 68 kg (±2.5) |
| VEHO 600 Pro V3 | 847 x 847 x 970 mm | Not listed |
| VEHO 500 Pro | 740 x 740 x 895 mm | Not listed |
| VEHO 4 | 650 x 620 x 602 mm | 22.5 kg |
Checklist
- Lift the larger models with two people. Never lift by the gantry or the bed.
- Place the 800 Pro and 600 Pro V3 on the floor or on a low, heavy-duty stand. The VEHO 4 fits on a sturdy desk.
- Leave space at the front for removing parts and at the sides and back for cables, spools and airflow.
- Use a dedicated wall socket. The VEHO 800 Pro is rated at up to 1800 W at 220 V.
- Keep the printer away from open windows, fans and air conditioning. Drafts are the main cause of warping on large parts.
- Remove all transport locks, zip ties and foam before powering on, and check that belts are tensioned and screws are tight after shipping.
Step 2: Understand how Klipper is controlled
Klipper reads its settings from a configuration file (usually printer.cfg) and accepts G-code commands from the touchscreen, the slicer, or a web interface if your printer offers one over the network. Many Klipper printers use a web interface such as Mainsail or Fluidd, which includes a console where you can type the commands in this guide.
Back up printer.cfg before you change anything, and use SAVE_CONFIG only after calibration commands that ask for it (it writes results to the config and restarts Klipper).
Step 3: Levelling: Z tilt correction and the 36-point mesh
Bed levelling on a large printer has two parts: first make the gantry and bed parallel, then measure the remaining surface variation with a mesh.
3a. Heat the bed first
Heat the bed to the temperature you print at most (for example 60°C for PLA) and wait 10 to 15 minutes. Large beds expand and warp slightly as they heat, so levelling a cold bed gives a mesh that does not match printing conditions.
3b. Home all axes
Run G28 to home X, Y and Z.
3c. Run Z tilt correction
The VEHO 800 Pro uses 4 Z motors with independent tilt correction, and the 600 Pro V3 and 500 Pro have 4 independent Z ball screws. In Klipper, this kind of correction is usually configured as a [z_tilt] section and run with:
Z_TILT_ADJUST
Klipper probes several points, calculates how far each Z motor is out, and adjusts them until the readings are within tolerance. Check your printer.cfg; if it uses a different section name, use the matching command your configuration defines. Run G28 again afterwards so Z is homed on the corrected plane.
3d. Set the Z offset
The Z offset is the distance between the probe trigger point and the nozzle. Too high and the first layer will not stick; too low and the nozzle scrapes the bed. With a standard probe setup, Klipper's procedure is:
PROBE_CALIBRATE
Then lower the nozzle in small steps (using TESTZ Z=-0.05 style moves or the on-screen adjust buttons) until a sheet of paper drags lightly, type ACCEPT, and SAVE_CONFIG. Fine-tune later during the first print with babystepping (Z offset adjustment while printing).
3e. Create the 36-point bed mesh
The VEHO models list a 36-point mesh, which is a 6 x 6 grid of probe points. In Klipper:
BED_MESH_CALIBRATE
SAVE_CONFIG
The mesh is stored as a profile (usually default). Your print start G-code should load it, for example with BED_MESH_PROFILE LOAD=default, or run a fresh mesh before each print. On an 800 mm bed, a fresh mesh before long prints is worth the extra minutes.
Tip: a large spread between the highest and lowest mesh point usually means debris under the plate, a plate not seated on the magnetic base, or a gantry that needs another Z tilt pass.
Step 4: PID tuning for the hotend and bed
PID tuning teaches Klipper how fast your heaters respond, so temperatures stay stable. This is especially important for the large bed. Run it at your typical temperatures:
PID_CALIBRATE HEATER=extruder TARGET=220
PID_CALIBRATE HEATER=heater_bed TARGET=60
SAVE_CONFIG
Repeat for higher temperatures if you mainly print ABS, PC or nylon blends.
Step 5: Input shaping
Input shaping reduces ringing (ghosting), the ripples that appear after sharp corners at high acceleration. The manufacturer lists input shaping for the VEHO 600 Pro V3, and it is a standard Klipper feature.
There are two common ways to tune it:
- With an accelerometer. If your printer has an accelerometer (such as an ADXL345) configured, run
SHAPER_CALIBRATE. Klipper measures resonances on X and Y and recommends a shaper type and frequency. Save withSAVE_CONFIG. - Without an accelerometer. Print a ringing test tower (Klipper's documentation provides one), measure the distance between ripples, and calculate the resonance frequency. Then set
shaper_typeandshaper_freq_x/shaper_freq_yin the[input_shaper]section.
After input shaping, Klipper also suggests a maximum acceleration for each shaper. On a large, heavy gantry, using that suggested value often gives cleaner prints than the absolute maximum on the spec sheet.
Step 6: Pressure advance
Pressure advance compensates for the pressure that builds up in the nozzle, which causes blobs at corners and gaps at the start of lines. The manufacturer lists pressure advance for the VEHO 600 Pro V3, and it is a standard Klipper feature for all Klipper printers.
Two ways to tune it:
- OrcaSlicer calibration. OrcaSlicer includes a pressure advance calibration test in its Calibration menu (line, pattern or tower method). Print the test, pick the cleanest result, and enter the value in the filament profile.
- Klipper tuning tower. Use
TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START=0 FACTOR=.005while printing a square test object, then choose the height with the sharpest corners and calculate the value.
Set the result in the [extruder] section (pressure_advance: 0.0xx) or per filament in OrcaSlicer. Re-tune when you change filament type or nozzle size, because the ideal value differs between PLA, PETG and TPU.
Step 7: Slicer profiles in OrcaSlicer
The VEHO 800 Pro lists OrcaSlicer, Cura and PrusaSlicer as compatible slicers. OrcaSlicer is a good choice for Klipper printers because it includes calibration tests and can send jobs over the network.
Setting up a printer profile
- Check whether OrcaSlicer includes a TRONXY VEHO preset for your model. If it does, start from it.
- If not, create a custom printer and enter the build volume from the spec sheet (for example 800 x 800 x 800 mm for the VEHO 800 Pro).
- Set the nozzle diameter to match the installed nozzle (0.4 mm is listed for the 600 Pro V3, 500 Pro and VEHO 4).
- Set G-code flavour to Klipper.
- Add start G-code that heats the bed, homes, runs Z tilt correction and loads or creates the bed mesh.
- Set the maximum volumetric speed in the filament profile. The VEHO 800 Pro and 600 Pro V3 hotends are rated up to 32 mm³/s; start lower (for example 15 to 20 mm³/s) and increase once prints are reliable.
- Run OrcaSlicer's flow-rate and pressure advance calibrations for each filament.
Useful profile settings for large parts
| Setting | Starting point for large PLA parts |
|---|---|
| Layer height | 0.2-0.3 mm (0.4 mm nozzle) |
| Walls | 3 |
| Infill | 5-15%, gyroid or cubic |
| First layer speed | Slow (20-30 mm/s) |
| Max volumetric speed | 15-20 mm³/s to start |
| Brim | 5-10 mm on tall or thin parts |
These are general starting points, not manufacturer settings.
Step 8: Your first large print
Start with a medium-sized part (30 to 50% of the build volume) before committing to a multi-day print, to confirm levelling, Z offset and adhesion across a large area.
Preventing warping
Warping is the most common failure on large parts: plastic shrinks as it cools, and bigger parts shrink more.
- Clean the bed. Wipe glass or PEI with isopropyl alcohol. Fingerprints ruin adhesion.
- Use the right bed temperature. Follow the filament maker's range. The VEHO beds reach 100-110°C depending on model.
- Add a brim. A 5 to 10 mm brim spreads the pull of shrinking corners. Mouse ears (small discs at corners) work for flat parts.
- Reduce part cooling for ABS, PC and nylon. Strong fans increase warping on these materials.
Enclosure and draft control
None of the VEHO specs list a full enclosure. For PLA and PETG in a calm room, this is rarely a problem. For ABS, PC and nylon blends on large parts:
- Use a draft shield (a slicer option that prints a thin wall around the part) to keep warm air near the print.
- Place the printer in a closed room without drafts, or build a simple enclosure around it with good ventilation for fumes.
- Keep the room temperature stable overnight.
During long prints
Check the first layer across the whole part, keep the filament run-out sensor active (listed on the VEHO 800 Pro and 600 Pro V3), and dry PETG, PA, PC and TPU before multi-day prints. After moving the printer or changing the build plate, re-run Z tilt correction and a fresh mesh.
For help choosing a model, see the VEHO 800 Pro vs 600 Pro V3 vs 500 Pro vs VEHO 4 comparison and the VEHO 800 Pro buyer's guide. For project ideas, read what you can print with an 800 mm 3D printer.
Frequently asked questions
How do I level a TRONXY VEHO printer?
Heat the bed, home all axes, run Z tilt correction (in Klipper usually Z_TILT_ADJUST) to align the four Z drives, set the Z offset, then create the 36-point bed mesh with BED_MESH_CALIBRATE and save it.
What is a 36-point bed mesh?
It is a 6 x 6 grid of probe measurements across the bed. Klipper uses it to compensate for small height differences in the build surface while printing, which matters a lot on a large bed.
Do I need an accelerometer for input shaping?
No, but it makes tuning faster. With an accelerometer, Klipper's SHAPER_CALIBRATE measures resonances automatically. Without one, you can print a ringing test tower and calculate the frequency by hand.
How do I tune pressure advance on a VEHO printer?
Use OrcaSlicer's pressure advance calibration test or Klipper's TUNING_TOWER method, pick the value with the cleanest corners, and save it in the extruder settings or the filament profile. Re-tune for each filament type.
How do I stop large prints from warping?
Clean the bed, use the correct bed temperature, add a 5 to 10 mm brim, avoid drafts, reduce part cooling for ABS, PC and nylon, and use a draft shield or enclosure for those materials.
Which slicer should I use for a VEHO printer?
OrcaSlicer, Cura and PrusaSlicer are listed as compatible for the VEHO 800 Pro. OrcaSlicer is a practical choice for Klipper printers because it includes calibration tests for flow and pressure advance.
Next step
Choosing your VEHO? See the product pages for full specs and the current price: VEHO 800 Pro, VEHO 600 Pro V3, VEHO 500 Pro and VEHO 4.